Announcement

Collapse
No announcement yet.

Expert offers "failure theory"

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Expert offers "failure theory"

    This was copied from a longarm quilting forum. I don't have the author's name, but I believe he has a firm grip on reality. This explains all our recent troubles - hard drives, images etc., and David, this might just be all the education you need.

    (Didn't change anything!) Was it Gremlins or PMS I don't know....
    >
    >Definitely the Gremlins!! No doubt about it.

    Well, maybe, but you need to know the color of the gremlin. I have
    studied gremlin theory for two decades now and frankly, I'm not whelmed
    with it. There is a terrific lack of specificity and technical rational
    to back up gremlin theory. The physics of gremlin theory have come into
    question. However, we do need a theory to explain what happens when
    things break, and since things do that, I will offer up an alternate
    failure theory based on 33 years of engineering experience, the last 7
    of which have been devoted to quite a few failure investigations.

    Its well known that all electrical equipment runs on smoke. Mechanical
    equipment runs on noise. Electro mechanical equipment, like embroidery
    machines, runs on both smoke and noise. The smoke and noise are
    installed at the factory, and are intended to be a life time supply,
    although usually the manufacturer installs a little extra noise - but
    never any extra smoke (EPA rules doncha know). One can get an extended
    warranty against leaks in the smoke and noise gaskets, but for some
    unfortunate reason such a warranty doesn't seem to be available for the
    D1.

    Usually, as long as no smoke escapes (there is no practical way to put
    it back), and only a little noise, the machine will be fine with just
    adjustments. Replacing escaped smoke is usually more expensive and
    takes longer than replacing a little bit of escaped noise because
    replacing escaped smoke requires new parts, and there is usually a bit
    of extra noise factory installed in the parts as noted above - and with
    the current environmental rules, the installation of smoke into new
    parts at the factory has gotten very expensive.

    Machinery is in trouble if it starts leaking noise. If a lot of noise
    leaks out, it takes exponentially longer (the product of increasing
    noise volume and duration raised to the third power, usually) to repair
    and becomes proportionately more costly to fix. At some point the parts
    run out of noise, the machine stops for lack of noise power, and usually
    requires replenishment of noise with new parts since escaped noise can
    not be put back either. This theory, you will have noted, is totally
    consistent with failed machines being silent. They have run out of
    noise and won't work properly again until new parts full of noise are
    installed.

    It can get similarly quiet if it runs out of smoke. However, you can
    almost always tell if it was noise or smoke depletion that caused the
    problem.

    Noise doesn't smell.

    take care, Margaret

  • #2
    Finally! Something I can understand.

    Ed

    Comment


    • #3


      ... "This theory, you will have noted, is totally consistent with failed machines being silent. They have run out of noise and won't work properly again until new parts full of noise are installed."

      Makes a lot of sense to me!

      Comment


      • #4
        that's hilarious, thanks for posting that margaret!! wow, I never knew repair was so easy.. if my computer stops working, all I have to do is go into the shop to get a refill of smoke and noise

        - David

        Comment

        Related Topics

        Collapse

        • nebgranny
          Noise: Can anymore be done?
          by nebgranny
          Can not post full pic, but hope this is big enough. Still working on those really dark pictures. This one was taken at night at a football game. I have done a levels adjustment and then I ran it through neat image twice. I still have a good bit of the pixles as noted in posted image.

          ...
          10-22-2005, 07:12 PM
        • Ken Fournelle
          Noise Reduction in the Work Flow
          by Ken Fournelle
          Where do people like to use a noise reduction plug-in during he work flow? On the duplicate background layer at the beginning? After global corrections to color, contrast and levels? The end of the process?

          Ken
          09-05-2004, 04:02 PM
        • scott watson
          Noise Reduction
          by scott watson
          After trying out Noiseware, Neat Image and Noise Ninja plugins I decided to purchase Noiseware Pro.
          I would like to know when is the best time to get rid of the noise. On the images I work on I will be doing alot of cloning to remove various elements in the image.
          Do you think its...
          12-03-2006, 12:21 PM
        • gamedonechanged
          How to get rid of noise
          by gamedonechanged
          What's the best way to get rid of noise in photoshop? I have seen there are some plugins available like noiseware ect... but im after a photoshop method.

          Any ideas?

          Thanks
          04-19-2010, 07:29 AM
        • pure
          how to add noise with noiselayer correctly?
          by pure
          hi

          i am about to put a person into a ready shot scene, its film and grainy in color. the grain is intended, and the new shot is digital and there is no grain.
          so i built the person into the scene and added a layer above all person layers, selected the persons' alpha channel, filled...
          02-17-2007, 12:24 PM
        Working...
        X